Biofuel Tests at Zoo - Round Two

Test locomotive No. 1924 blasts up the 3% grade hauling a heavy train. The locomotive is being fired with 100% torrefied biomass fuel and is instrumented with test equipment to gauge firebed and smokebox temperatures.

Test locomotive No. 1924 blasts up the 3% grade hauling a heavy train. The locomotive is being fired with 100% torrefied biomass fuel and is instrumented with test equipment to gauge firebed and smokebox temperatures.

CSR and NRRI again collaborated with the Milwaukee County Zoo to undertake a comparative test of torrefied biomass fuel and coal this past October. The previous round of tests CSR undertook in June employed very small (3/8 inch diameter) cylindrical fuel pellets. While the finding of those tests were promising, CSR sought to undertake tests with fuel analogous in size to that employed on preserved steam locomotives.

The researchers at the Natural Resources Research Institute (NRRI) produced 500 lbs of torrefied biomass with its recently-commissioned torrefaction reactor and densified it using a B-100 cylindrical densifier to an approximate size of 1-1/4 x 2 inches [shown below, second from left]. These larger pieces of fuel were more analogous to the coal typically used by the Milwaukee County Zoo. As expected, the larger torrefied biomass pieces burned more cleanly in the firebox than the smaller pieces used in the previous round of testing.

As with the previous tests, CSR instrumented the locomotive with four thermocouples [shown at right], three in the firebox and one in the smokebox, to document temperatures on comparative tests between torrefied biomass combustion and coal combustion. To minimize the risk of sparks from coal/torrefied biomass fines, CSR also fabricated and installed a custom spark arrestor for use on the stack of the engine.

Tests revealed that the torrefied biomass burned with similar temperatures as the coal and with little smoke [see images at bottom]. It also revealed that the fuel has a very low ash content compared with coal.

That said, densification of the torrefied fuel still needs refinement to permit the fuel to burn more similar to coal, including for the same duration as coal per unit fired. The less dense torrefied fuel resulted in a quicker dropoff of firebox temperatures when the throttle of the locomotive was closed. These tests provided CSR with much needed data on the characteristics of torrefied biomass combustion in locomotive-style boilers, and it has provided focus for research this winter.

The cooperation of the Milwaukee County Zoo has been second-to-none in undertaking these tests, and it has provided CSR with a very good platform to undertake research. Whereas running tests in a full-size locomotive would take thousands of pounds of fuel, the Milwaukee County Zoo locomotive No. 1924 can operate a full day on 500 lbs of fuel or less. This keeps costs low in developing various fuel typologies (wood stock varieties, densification types, etc.), while still having a one third scale engine on which to test the effects of drafting and combustion.

With these tests completed, CSR is working with NRRI to undertake densification research over the winter. CSR will provide more information on those plans, including proposed future tests on standard gauge equipment, in the coming weeks.

In the meantime, please consider making a tax-deductible contribution to CSR to support the upcoming tests and research!

Firing up on coal, the locomotive had little difficulty making smoke.

Firing up on coal, the locomotive had little difficulty making smoke.

Once switched to torrefied biomass fuel, the locomotive made almost no smoke.

Once switched to torrefied biomass fuel, the locomotive made almost no smoke.

Members of the CSR / Zoo research team pose in front of the two steam locomotives operated by the Zoo.• People, from left to right: Davidson Ward [CSR]; Ken Ristow [Zoo]; Rob Mangels [CSR]; and Wolf Fengler [CSR].• Locomotives, from left to right: 4…

Members of the CSR / Zoo research team pose in front of the two steam locomotives operated by the Zoo.

• People, from left to right: Davidson Ward [CSR]; Ken Ristow [Zoo]; Rob Mangels [CSR]; and Wolf Fengler [CSR].
• Locomotives, from left to right: 4-4-2 No. 1916, burning coal; and 4-6-2 No. 1924, burning torrefied biomass - both manufactured by Sandley Light Railway Equipment Works, Wisconsin Dells, Wisconsin.

,

A Primer on the Lempor Exhaust

,

While we have mentioned the Lempor in some of our White Papers, and we will focus a new White Paper specifically on exhaust systems in the near future, the CSR Team thought it might be helpful to give some insights into the physics given that both Grand Canyon Railway steam locomotives No. 29 and No. 4960 are now back in service and that both have Lempor Exhausts designed by Nigel Day. 

This video, courtesy of Chris Zahrt, shows GCRy No. 29 hustling a train under stormy skies. The 1906-built 2-8-0 burns used vegetable oil and employs a Lempor Exhaust to use steam as efficiently as possible within the constraints of the historic locomotive.

Understanding drafting in steam locomotives starts in the cylinder at the point of release [C on the following diagram]. This is when the valve first opens to let exhaust steam out of the cylinder. The pressure in the cylinder at release depends largely on the cutoff selected. A long cutoff means that the cylinder has been filled with near-boiler pressure steam for the majority of the stroke, which prevents the steam from expanding much before exhaust, therefore leading to a higher pressure at release. A short cutoff allows steam to enter the cylinder for a shorter percentage of the stroke, providing a proportionately longer percentage of the stroke for the steam to expand and, thus, exhausting with a lower pressure. Regardless of the pressure at the release point, the steam pressure in the cylinder drops quickly as the steam flows out and fills the exhaust steam passages [E]. The pressure at the cylinder exit [C] will eventually stabilize to a level determined by the total cross-sectional area of the exhaust nozzle(s) and the mass flowrate of steam. This stabilized pressure is known as "back pressure."

CLICK TO ENLARGE This diagram compares a "Normal" U.S. exhaust nozzle system with the advanced "Lempor" system, as equipped on GCRy Nos. 29 and 4960. Both types share similar components of: 1) Branch Pipes [live steam]; 2) Valves [live and exhaust stem]; 3) Piston [live and exhaust steam]; and 4) Exhaust passage. Where they differ is the design of: 4A/4B) the exhaust paths; 5A/5B) the type of nozzle; 6A/6B) the design of the petticoat; and 7A/7B) the refinement in design of the stack.

Between the cylinder [3 in the diagram above] and the exhaust nozzle [5A], some of the energy left in the steam will be lost due to factors such as: passages being too small; turns being too sharp; sudden changes in passage size; passages walls being too rough; or excessive heat loss due to design / lack of insulation. In some very poorly designed locomotives, the exhaust passages can be joined in ways such that the exhaust pressure pulse from one side of the cylinder can be "seen" by the opposite cylinder which creates an artificially higher back pressure [as exhibited above near the number 4A].

Bernoulli's equation helps us understand the relationship of pressure and velocity in fluid flows. Without delving too deeply into the details, the equation tells us that a high speed flow equates to a lower pressure and a low speed flow leads to higher pressure. Taking a look at the locomotive exhaust nozzle [5A], the idea is to transfer the "pressure energy" of the steam into velocity to create a low pressure region just outside the nozzle which will suck the exhaust gasses from the firebox through the flues. For a given back pressure, a smaller nozzle opening (aka "cross-sectional area") will give a higher velocity flow and, thus, a strong draft on the fire. However, that back pressure may become high enough to start limiting the power that can be produced in the cylinders. This is exhibited in the relationship between the difference in pressure going in and going out of the cylinders. 

Normally, to get more power, one would simply increase the cross-sectional area of the nozzle opening, lowering the back pressure at the same cylinder inlet pressure and cutoff. While this may increase power, it decreases the velocity of steam exiting the nozzle and, in turn, also decreases the draft acting on the fire and drawing hot gasses through the boiler. The result would be a poorly-drafting locomotive that would have difficulty making steam to meet the improved power from the cylinders.

Whereas the above describes a traditional single nozzle exhaust, a Lempor nozzle splits the total steam flow between four separate, smaller nozzles [5B]. Assume that the total cross-sectional opening for the four Lempor nozzles is the same as a single nozzle [5A]. Under the same inlet pressure and other conditions, the local speed of the steam jet exiting the smaller openings of the four nozzles will be a fair bit higher that that of the single, larger nozzle, simply because of the relationship between opening size and velocity. This creates a stronger draft with the same back pressure. The steam locomotive designer now has more options for finding an optimal balance between cylinder power and draft.

Steam locomotive mechanical engineer L.D. Porta also introduced a converging-diverging, or DeLaval, nozzle to steam locomotive design [5B]. In all other steam locomotive exhaust nozzles that we are aware of prior to his application, the exit walls were essentially parallel to the direction of steam flow. Under subsonic conditions, the converging or narrowing section works to speed up the flow. Once the flow reaches choked conditions, basically a velocity of Mach 1, no further acceleration can be obtained and thus no more improvement in draft. The diverging, or widening, portion of the nozzle under subsonic conditions actually serves to slow down the flow and increase the pressure. However, things flip-flop once the flow goes supersonic and by allowing the nozzle to widen to the outlet, the steam jet can continue to accelerate leading to draft improvement.

The multiple nozzles also help with mixing of the steam and flue gas as they lead to more surface area of steam at high velocity in contact with the flue gas. [Note that without good mixing of the two streams, the flue gas would mostly just stay in the smokebox instead of exiting the stack and its velocity through the flues and tubes would be much lower, resulting in poor heat transfer and thus poor steaming.] While mixing takes place as soon as the steam exits the nozzle, the first section of the petticoat [6B] is specifically thought of as a mixing chamber and its proportions in concert with those of the nozzles help assure good mixing/momentum transfer from the high velocity steam to the lower velocity flue gas.

Once mixed, the steam and flue gas is in the subsonic flow region but still has a fair bit of energy left and is still flowing at a fairly high velocity. If it was just allowed to go up a straight stack to the atmosphere [7A], that energy would be lost. Therefore, the latter part of the Lempor petticoat widens out [7B], which slows the flow and increases its pressure back to that of atmospheric. This characteristic, widening stack can be seen in the diagram of No. 29 below.

As in much of fluid mechanics, it takes very careful calculation and proportioning to maximize the benefit of the system which can be significant compared to other known exhausts. Failure to do so, either through poor engineering or when physical or other constraints restrict the designer's ability to implement a properly sized system will lead to a poor performing product.

Upcoming White Paper

The CSR Team is working on a White Paper dedicated to the development of advanced steam exhaust systems, from the traditional U.S. designs through Chapelon to Giesel and Lempor. Expect more information on that in the coming month. To stay up to date on CSR, consider signing up for our email list at the bottom of this page.

Footage of First Torrefied Biomass-Run Train

This video shows the first run of the torrefied biomass test train on the Milwaukee County Zoo mainline, with footage of the train starting from the point the shop lead connects with the tracks and operating to the summit, approximately 1/2 mile. We have synced up the readings from the four thermocouples with the video footage, showing a second-by-second readout of combustion temperatures in the locomotive.

While watching the video, note that Zoo crew member, Ken Ristow, is hand shoveling loads of the small, torrefied biomass pellets into the firebox. The fuel pellets, which were graciously donated to CSR for these tests by New Biomass Energy, are much smaller than the coal typically used on a steam locomotive. We therefore modified the grates with stainless steel mesh to prevent the fuel from falling through the large pinholes. Due to the small size of the fuel, we could only build up a thin firebed (2" with biomass vs. 5" on coal), meaning there was less potential energy in the fire, resulting in the need to shovel more frequently than with coal. Likewise, NBE's pellets exhibited such good flowability, which is very important in stoker firing, that they were prone to slide off of the coal scoop.

CSR is working with research collaborator Natural Resources Research Institute and the Milwaukee County Zoo to schedule another round of testing later this year with larger, "puck" sized torrefied biomass briquettes to further verify the promising results produced from these initial tests. Likewise, we have been in discussion with standard gauge steam operators about performing full size tests in the future.

In all, the Milwaukee County Zoo tests were an extremely important scientific and risk mitigation step in this research. They allowed CSR the opportunity to collect comparative data on the combustion of coal vs. torrefied biomass (which will be made available in the coming months as part of a larger White Paper) and it proved that steam locomotives could make steam and operate safely using the alternative fuel. 

We could not have done these tests without the outstanding assistance of the Milwaukee County Zoo, the Natural Resources Research Institute, New Biomass Energy, the American Boiler Manufacturers Association, and the support of CSR's donors, including generous contributions by Bon French and Fred Gullette.

If you'd like to help make the next set of tests happen, please consider:

CSR Undertakes First Test of Biocoal with a Steam Locomotive

Milwaukee County Zoo locomotive number 1924 served as the "guinea pig" on these first torrefied biomass tests. Operating on 15 inch gauge track, the locomotive is the perfect scale to begin combustion analyses of torrefied fuel under the highly vari…

Milwaukee County Zoo locomotive number 1924 served as the "guinea pig" on these first torrefied biomass tests. Operating on 15 inch gauge track, the locomotive is the perfect scale to begin combustion analyses of torrefied fuel under the highly variable drafting of steam locomotive boilers.

From June 10-12, CSR teamed up with the Milwaukee County Zoo, the Natural Resources Research Institute, and New Biomass Energy to undertake the first test of torrefied biomass on a steam locomotive. The tests are a key step in ensuring that the fuel can be used in steam locomotives of all sizes in the face of shuttering coal mines. 

Torrefied biomass pellets used in the testing.

The Milwaukee County Zoo operates two steam locomotives on its 15 inch gauge railroad. With just over a mile of mainline track and upwards of 30 trains per day, the Zoo operation provided CSR the opportunity to compare runs burning coal with identical runs burning "torrefied biomass," also known as "biocoal," in a controlled, test-scale environment.

"We instrumented the locomotive with four, Inconel-sheathed thermocouples to gauge firebed, combustion space, and exhaust gas temperatures when burning coal vs biocoal," explained CSR Senior Mechanical Engineer Wolf Fengler. "Tests were run on Saturday and Sunday, with trains Saturday burning coal and the first runs of Sunday burning biocoal."

Modified grates [bottom] and two of the three thermocouples poking through staybolt telltale holes [left]. Click to Enlarge

CSR worked hand-in-hand with Zoo staff to instrument 4-6-2 steam locomotive number 1924 and undertake the tests [see diagram below]. Torrefied biomass fuel was graciously donated by New Biomass Energy for use during research. The small fuel pellets were burned on a modified stainless steel grate installed by CSR on-site.

"We used National Instruments hardware in concert with its LabView software to record second-by-second temperature data from the sensors," said CSR President Davidson Ward. "Perhaps most exciting was the fact that three of the sensors were directly in the firebox, one submerged in the firebed and two at varying heights above, each of which provided better insights into the combustion behaviors of each fuel."

[Click to Enlarge]

While data processing is still underway, initial results indicate that the torrefied biomass fuel burns with a very similar temperature profile as the coal used by the Zoo, but the biomass had a much longer flame profile, which bodes well for producing more uniform stresses in the firebox.

The video below shows a comparison of coal with biocoal under identical, hostling circumstances. Note the length of flame and brightness of the fire generated by the torrefied biomass.

More information, including additional videos of the tests and a detailed White Paper, will be made available later this summer. CSR plans to undertake a second set of tests with the Milwaukee County Zoo with larger torrefied biomass pellets created by NRRI at its Coleraine Minerals Research Laboratory later this year. The organization has also been in discussions with standard-gauge operators about undertaking full scale tests in the future.

The Milwaukee Zoo train tests were made possible by the outstanding assistance of the Milwaukee County Zoo, the Natural Resources Research Institute, New Biomass Energy, the American Boiler Manufacturers Association, and the support of CSR's donors, including generous contributions by Bon French and Fred Gullette.

If you have yet to do so, please:

Dedicated to: Randy Rawson

For the duration of biofuel testing, CSR renamed locomotive 1924 "Randy Rawson" in honor of the former President of the American Boiler Manufacturers Association, W. Randall Rawson, who died in November 2013. He was a superb friend and advocate of CSR, having expressed unwavering interest and support of our biofuel and steam locomotive research. He had always wanted to be present for the first tests of torrefied biomass in a steam locomotive, and we wanted to do our part to honor him. To this day, Rawson's legacy, sense of humor, and enthusiasm continue to serve as an inspiration to the leaders of CSR. 

How it Works - Phoenix Log Hauler

A typical"tech tuesday" video post has received a great deal of attention in the past week. Posted Tuesday, July 12, on CSR's Facebook Page, the video [embedded below] of Wabeno's Phoenix Log Hauler has received, as of Friday, more than 170,000 views in three days. The unique vehicle, largely unknown to those outside of rural northern Wisconsin, is most likely why the video has been so popular.

That uniqueness is also what attracted CSR President Davidson Ward to visit Wabeno and attend its annual "Steam Up Days" festival the weekend prior.

"I had run across the Phoenix Log Hauler parked and under cover when driving through the town on a road trip two years prior," explained Ward. "When the opportunity arose to visit friends in the region and see the 'Phoenix' in action, I couldn't say no."

The Phoenix Manufacturing Company of Eau Claire, Wisconsin, manufactured the unique piece of steam history in the early 1900's for use by the G.W. Jones Lumber Company at its mill from 1909 to 1935.

The machine is a unique mixture of steam locomotive, steam tractor, and treaded-excavator that was used to haul long sleds of logs from the forests to the lumber mill in Wabeno, Wisconsin. It was used in both summer and winter, with two skis attached in place of the wheels for winter operations. Interestingly enough, the device burns hardwood scraps and uses water picked up along the way (or from snow), and it could thereby be an example of "old school sustainability." Click on the diagram below to get an enlarged view of the machine.

The "Phoenix" was donated to the Town of Wabeno in 1944 by the lumber company, and a group of citizens restored it to operation in 1965. The unique machine is one of only a few similar to it operating today, with the majority of other surviving machines having been made by Lombard in Maine (Lombard licensed components of its invention to Phoenix for the manufacture of this and about 200 other units made by the company).

Each year on the weekend after the Fourth of July, Wabeno hosts a "Steam Up Days" to show off its unique, operating piece of history and host a bunch of other lumberjack-related equipment. It is a good time and an event not to be missed!

Be sure to follow CSR to stay up-to-date on interesting innovation and preservation news:

Axles vs. Axis - Memorial Day 2016

The U.S. railroads banded together with the nation to help win the Second World War, and a large portion of that included promoting war bonds and recognizing the accomplishments of the railroad in supporting the Allied war effort. This ad shows many pieces of the "Axles vs. Axis" of the ATSF, including an engineman lubricating the driving box pedestals of ATSF 3460. 

On this Memorial Day, CSR remembers and honors the ultimate sacrifice given by so many in support of freedom - from those who rode to the front lines behind ATSF steam locomotives to those who have defended our freedom before and since. To all, we are forever grateful.